SunSDR2PRO with control panel

Transceiver with a control panel.

The bundle includes a SunSDR2PRO transceiver and an E-Coder2 control panel. The main specifications below refer to the transceiver.

HF
15W
ADC
16bit
In bundle
2pcs
6 m
15W

Transceiver features

Contests and SO2R

Two independent software receivers, each with a sub-receiver, allow reception on two HF bands and split operation for DX. Use the appropriate connection diagram for a contest setup with peripherals controlled over ExtCtrl.

Home shack and field

130 dB dynamic range on HF and 114 dB on VHF, 0.2 µV sensitivity and a +10 dB preamp keep you confident on a crowded band.

Field power

10–16 V on receive and 12–16 V on transmit: a switching supply or a battery will do.

2 m VHF and transverters

A built-in +22 dB VHF LNA and transverter support. With an external amplifier the PRO runs the whole set-up, and the kit stays portable.

Control panel

The panel has a main tuning encoder with 1024 PPR resolution, 14 programmable buttons with templates for 72 functions, and 3 programmable rotary encoders with push-button functions. It connects via USB and supports macOS, Windows and Linux.

Audio and monitoring

E-Coder2 is a new-generation control panel with a built-in 24-bit audio codec and a dynamic range of 114 dB (CS4272).

When you operate in RX mode, the ExpertSDR2/3 sends the same audio stream in the TRX and in the E-Coder2. Thus, you can listen to the air directly from the TRX or from the E-Coder2, the latency in both cases is the same - almost nonexistent. Also, in E-Coder2 we've implemented a special CW core to minimize latency if you monitor yourself during transmission.

E-Coder2 control panel

Remote operation

E-Coder2 is especially useful for users of remote-control systems or those operating some distance from the transceiver.

Connections and power

The USB port must provide 5 V and at least 0.5 A. The rear panel has four 6.3 mm stereo jacks: headphones, an unbalanced microphone, a CW key and a PTT footswitch.

Use cases

  • 01

    Contesting

    Two software receivers let you monitor different parts of the band and operate split. Use the appropriate connection diagram for an SO2R/SO2V setup.

  • 02

    DX Hunting

    A wide spectrum display and an instant jump to the caller's frequency in split operation give an advantage in pile-ups.

  • 03

    Remote Operation

    Streaming audio and the spectrum display over the internet enables operation from anywhere in the world.

  • 04

    Digital Modes (FT8/FT4)

    Direct integration with WSJT-X and loggers over TCI, without virtual audio cables.

ExpertSDR3, TCI and ERS

Free ExpertSDR3 with free updates. The open TCI protocol connects loggers, skimmers and digital-mode programs without virtual COM ports or audio cables; programs without TCI use the RadioSync bridge (CAT, OmniRig). Expert Remote System (ERS) is included: control from a browser or ExpertSDR3, directly or through the ExpertCloud service.

About the software
  • ExpertSDR3Free software for operating on the air
  • TCIAn open protocol for loggers, skimmers and digital modes
  • ERSRemote operation from a browser or ExpertSDR3

Hardware section

  • ALC*

    Input for external power amplifiers, controlled over ExtCtrl.

  • Full Duplex*

    Full-duplex operation.

* The hardware supports these functions; software support comes in ExpertSDR3 updates.

SpecificationsSunSDR2PRO with control panel

Receiver Characteristics

Receiver Characteristics
RF ADC, resolution16 bit
RF ADC, sampling rate160 MHz
ADC typeLTC2209
RX Frequency range0.1...65; 95...155 MHz
Sub-receivers2 pcs
Sample rate39; 78; 156; 312 @ 24 kHz / bit

See all specifications for details

SunSDR2PRO — Antennas and receive input
SunSDR2PRO — Antennas and receive input

Transmitter Characteristics

Transmitter Characteristics
RF DAC, resolution14 bit
RF DAC, sampling rate640 MHz
TX Frequency range160-6; 2 m
Output power on HF15 (up to 20) W
Output power on 6M15 W
Output power on VHF7 (up to 8) W

See all specifications for details

SunSDR2PRO — External device control
SunSDR2PRO — External device control

Specifications

Specifications
Local oscillator TCXO, frequency20 MHz
Local oscillator TCXO, accuracy±0.5 ppm
External 10 MHz oscillator inputYes
RF input/output2 HF, 1 VHF, ADC IN, DAC OUT
PC interfaceLAN 100 Mbps
DC voltage range in RX/TX10...16 / 12...16 V

See all specifications for details

SunSDR2PRO — Front panel
SunSDR2PRO — Front panel

Documentation and package contents

© 2026 Expert Group LLC