Amplifier PA50WV

50 W for the 2 m band.

VHF amplifier for 136–174 MHz. Input and output impedance: 50 ohms; low-noise amplification on receive; 12–16 V supply.

Power
50W
Impedance
50ohm
Weight
1.7kg
Band
2 m

Capabilities

Linear amplification

PA50WV is a 50 W power amplifier for linear amplification of RF signals on the 2 m band.

  • A Mitsubishi RA60H1317M amplifier module is used to deliver 50 W of VHF output power.
  • The amplifier uses a conventional single-ended circuit and supports all modulation modes.

No retuning required

Active broadband components eliminate the need for adjustment or tuning throughout the operating frequency range.

  • Active cooling allows continuous-carrier operation for extended periods at full output power.

Operating scenarios

  • 01

    Long-distance contacts

    For operators making long-distance contacts on the 2 m amateur band.

  • 02

    Digital modes

    Long transmit cycles, including digital modes, with active amplifier cooling.

  • 03

    Vehicle installation

    Installation in a vehicle together with a SunSDR2PRO transceiver.

Features

50 W

Output power up to 50 W over the 136–174 MHz range. The amplifier is designed for extended operation, including digital modes.

1 W or 5 W input

The Pin button selects the setting for 1 W or 5 W of input power.

Compact format

Dimensions including the cooling module: 185 × 165 × 83 mm; weight: 1.7 kg. The compact format is suitable for field operation and DXpeditions.

Built-in LNA

The +19.5 dB low-noise amplifier is enabled with the LNA button and operates on receive. Its power is removed when switching to transmit.

LNA in practice

With the TX input open, the amplifier operates in receive mode. The LNA button enables the low-noise amplifier with +19.5 dB gain. The LNA is automatically powered down on transmit; the illuminated LNA indicator shows the selected mode. The measurement was made with a SunSDR2 PRO: 145.1 MHz, CW, 500 Hz bandwidth, and a −110 dBm input signal.

Without the LNA, the signal measured −112.2 dBm and the noise −122.4 dBm; with the LNA, they measured −93.9 and −120.3 dBm. The signal increased by 18.3 dB, the noise by 2.1 dB, and the signal-to-noise ratio improved by 16.2 dB: a weak station is received more reliably. The improvement depends on the antenna, feed line and noise conditions; the lower the receiver's own noise, the less an external preamplifier will contribute. These figures are the result of a specific measurement, not a guaranteed specification.

LNA in practice

Connections and controls

Front panel

  • FWD indicates RF power transmission.
  • REF indicates an SWR above 3:1. There is no automatic SWR shutdown: stop transmitting and check the antenna and feed line.
  • Pin selects an input level of 1 W or 5 W.
  • LNA enables the +19.5 dB receive preamplifier; an open TX control input corresponds to receive mode.
  • On transmit, LNA power is removed, but the LNA indicator continues to show the selected mode.
  • PWR switches the amplifier on. When it is off, ANT and RADIO are connected directly.

Rear panel

  • ANT connects a 50-ohm antenna.
  • +12V connects a 12–16 V, 16 A power supply.
  • TX accepts the external transmit-control signal.
  • RADIO connects a transceiver with a 50-ohm output.

Amplifier control

The amplifier switches to transmit in response to an external control signal from the transceiver through the “TX” connector. PA50WV has no RF detector: an input signal alone does not switch it to transmit, so the transceiver must provide a PTT control output.

Pin selects a 1 W or 5 W input level; nominal output is 50 W in either setting. Output depends linearly on the drive power: 2.5 W in the 5 W setting gives roughly half the output power. There is no separate power control or ALC; set power at the transceiver.

Set the maximum drive in the transceiver software’s “Power correction” menu. The firmware-level limit restricts power spikes that could damage the amplifier. Do not exceed the input power allowed by the selected setting.

SpecificationsAmplifier PA50WV

Specifications

Specifications
Amplifier control connector typeRCA
Frequency coverage136...174 MHz
Input/output impedance50 ohm
Input signal amplifier in receive mode+19.5 dB
Nominal output power50 W
Power connector typeAnderson Power Pole

See all specifications for details

Specifications
Specifications

Reference and package contents

© 2026 Expert Group. All rights reserved.