SunSDR2DX with tuner & control panel
Transceiver with a tuner and control panel.

01 / 04 — SunSDR2DX, AAT-100 and E-Coder2 bundle — complete set
The bundle includes a SunSDR2DX transceiver, an AAT-100 antenna tuner and an E-Coder2 control panel. The main specifications below refer to the transceiver.
- HF
- 100W
- ADC
- 16bit
- In bundle
- 3pcs
- 6 m
- 80W
Transceiver features
100 W and a DDC/DUC architecture
- Direct sampling on receive (DDC) and direct digital synthesis on transmit (DUC), with separate receive and transmit paths.
- 16-bit LTC2209 ADC with a 160 MHz sampling rate.
- A quiet 140 × 140 mm fan and stable operation through long transmit cycles on digital modes.
Two independent receivers
- Two software receivers, each with a sub-receiver; reception 0.1–65 and 95–155 MHz.
- Panorama up to 312 kHz and a band scope up to 80 MHz.
- Simultaneous reception on different HF bands and split operation. Use the appropriate connection diagram for a contest setup with peripherals controlled over ExtCtrl.
AAT-100 antenna tuner
The AAT-100 automatic antenna tuner is designed to connect to a SunSDR2DX transceiver. The maximum allowed SWR is 3.5.
The tuner matches the antenna to the transceiver within its operating limits. Antenna tuning is initiated from the software.

Control panel
The panel has a main tuning encoder with 1024 PPR resolution, 14 programmable buttons with templates for 72 functions, and 3 programmable rotary encoders with push-button functions. It connects via USB and supports macOS, Windows and Linux.
Audio and monitoring
E-Coder2 is a new-generation control panel with a built-in 24-bit audio codec and a dynamic range of 114 dB (CS4272).
When you operate in RX mode, the ExpertSDR2/3 sends the same audio stream in the TRX and in the E-Coder2. Thus, you can listen to the air directly from the TRX or from the E-Coder2, the latency in both cases is the same - almost nonexistent. Also, in E-Coder2 we've implemented a special CW core to minimize latency if you monitor yourself during transmission.

Remote operation
E-Coder2 is especially useful for users of remote-control systems or those operating some distance from the transceiver.
Connections and power
The USB port must provide 5 V and at least 0.5 A. The rear panel has four 6.3 mm stereo jacks: headphones, an unbalanced microphone, a CW key and a PTT footswitch.
Use cases
- 01
Home shack
Full power without an external amplifier, tuning from the E-Coder2 panel instead of a mouse.
- 02
Contest position
Split operation in pile-ups and a CW skimmer over TCI. Use the appropriate connection diagram for an SO2R/SO2V setup.
- 03
DX expeditions
Full power in a compact case, from the tropics to the Arctic.
- 04
Digital modes
Reliable operation through long FT8 transmit cycles.
- 05
VHF
Operation on 2 m, connection to a PA50WV amplifier, and transverter support.
- 06
QO-100 satellites
Hardware groundwork for full duplex and transverters.
ExpertSDR3, TCI and ERS
Free ExpertSDR3 with free updates. The open TCI protocol connects loggers, skimmers and digital-mode programs without virtual COM ports or audio cables; programs without TCI use the RadioSync bridge (CAT, OmniRig). Expert Remote System (ERS) is included: control from a browser or ExpertSDR3, directly or through the ExpertCloud service.
About the software- ExpertSDR3Free software for operating on the air
- TCIAn open protocol for loggers, skimmers and digital modes
- ERSRemote operation from a browser or ExpertSDR3
Hardware section
ALC*
Input for external power amplifiers; today control runs over ExtCtrl.
Full Duplex*
Full-duplex operation.
Predistortion*
Predistortion for a clean signal without external devices.
* The hardware is ready; software support is planned in ExpertSDR3 updates.
SpecificationsSunSDR2DX with tuner & control panel
Receiver Characteristics
| RF ADC, resolution | 16 bit |
|---|---|
| RF ADC, sampling rate | 160 MHz |
| ADC type | LTC2209 |
| RX Frequency range | 0.1...65; 95...155 MHz |
| Sub-receivers | 2 pcs |
| Sample rate | 39; 78; 156; 312 @ 24 kHz / bit |
See all specifications for details
Transmitter Characteristics
| RF DAC, resolution | 14 bit |
|---|---|
| RF DAC, sampling rate | 640 MHz |
| TX Frequency range | 160-6; 2 m |
| Output power on HF | 100 W |
| Output power on 6M | 80 W |
| Output power on VHF | 7-8 W |
See all specifications for details
Specifications
| Built-in audio codec / Dynamic Range | 24 / 114 bit/dB |
|---|---|
| RF input/output | 2 HF, 1 VHF (Mini_UHF), ADC IN, DAC OUT (SMA) |
| DC voltage range in RX/TX | 8...14.8 / 10...14.8 V |
| Recommended DC voltage | 13.8 V |
| Current consumption RX/TX | 1.2 / 24 A |
| Power consumption RX/TX | 16.5 / 330 W |
See all specifications for details




