Amplifier PA50WU

50 W for the 70 cm band.

Discontinued

A UHF amplifier for frequencies from 400 to 480 MHz. 50-ohm input and output impedance, a low-noise amplifier for reception, and a 12–16 V power supply.

Power
50W
Impedance
50ohm
Weight
1.7kg
Band
70 cm

Discontinued

No longer sold. The page stays for owners: specifications and software compatibility.

Capabilities

Linear amplification

PA50WU is a 50 W power amplifier for linear amplification of RF signals on the 70 cm band.

  • The Mitsubishi RA60H3847M1A-501 amplifier module delivers 50 W of output power.
  • The amplifier uses a conventional single-ended circuit and supports all modulation modes.

No retuning required

Active broadband components eliminate the need for adjustment or tuning throughout the operating frequency range.

  • Active cooling allows continuous-carrier operation for extended periods at full output power.

Operating scenarios

  • 01

    Long-distance contacts

    The amplifier is intended for enthusiasts of long-distance contacts on the 70 cm amateur radio band.

  • 02

    Digital modes

    Extended transmission cycles, including in digital modes, with active cooling of the amplifier.

  • 03

    Vehicle installation

    The compact enclosure is suitable for a vehicle installation on the 70 cm band.

Features

50 W

Output power of up to 50 W over the 400–480 MHz range. The amplifier is designed for extended operation, including in digital modes.

1 W or 5 W input

The Pin button selects the setting for 1 W or 5 W of input power.

Compact format

Dimensions including the cooling module: 185 × 165 × 83 mm; weight: 1.7 kg. The compact format is suitable for portable operation and DXpeditions.

Built-in LNA

The +19.5 dB low-noise amplifier is enabled with the LNA button and operates on receive. Its power is removed when switching to transmit.

Enclosure indicators

Show power, the selected input-power level and LNA mode.

LNA in practice

With the TX input open, the amplifier operates in receive mode. The LNA button enables the low-noise amplifier with a gain of +19.5 dB. LNA power is automatically removed during transmission; the lit LNA indicator shows the selected mode. The measurement was made with a SunSDR2 PRO: 145.1 MHz, CW, a 500 Hz bandwidth and an input signal level of −110 dBm.

Without the LNA, the signal was −112.2 dBm and the noise was −122.4 dBm; with the LNA, the values were −93.9 and −120.3 dBm. The signal increased by 18.3 dB, the noise by 2.1 dB, and the signal-to-noise ratio improved by 16.2 dB: a weak station can be received more reliably. The improvement depends on the antenna, feed line and noise conditions; the lower the receiver’s own noise, the less an external preamplifier will add. These figures are the result of a specific measurement, not a guaranteed specification.

LNA in practice

Amplifier control

FWD indicates RF power transmission.

REF indicates an SWR above 3:1.

Pin selects an input level of 1 W or 5 W.

LNA enables the +19.5 dB receive preamplifier; an open TX control input corresponds to receive mode.

On transmit, LNA power is removed, but the LNA indicator continues to show the selected mode.

PWR switches the amplifier on. When it is off, ANT and RADIO are connected directly.

ANT connects a 50-ohm antenna.

+12V connects a 12–16 V, 16 A power supply.

TX accepts the external transmit-control signal.

RADIO connects a transceiver with a 50-ohm output.

SpecificationsAmplifier PA50WU

Specifications

Specifications
Amplifier control connector typeRCA
Frequency coverage400...480 MHz
Input/output impedance50 ohm
Input signal amplifier in receive mode+19.5 dB
Nominal output power50 W
Power connector typeAnderson Power Pole

See all specifications for details

PA50WU — front and rear panel drawing
PA50WU — front and rear panel drawing

Reference and package contents

© 2026 Expert Group LLC